Rockbox.org home
release
dev builds
extras
themes manual
wiki
device status forums
mailing lists
IRC bugs
patches
dev guide



Rockbox mail archive

Subject: Re: HD Crash after a battery reset?
From: Jason Williams (jason_at_redskycomputing.co.uk)
Date: 2002-08-15


Looks like the Partition info is corrupt, Repartition and format required.
----- Original Message -----
From: "Lucas Vergnettes" <lucas_at_thinko.net>
To: "RockBox ML" <rockbox_at_cool.haxx.se>
Sent: Thursday, August 15, 2002 2:43 PM
Subject: HD Crash after a battery reset?

> Hi All
>
> After resetting my AJBR20 but putting batteries away for a minute, it
> rebooted on the orig firmware saying "Can't read disk".
> I cannot mount it on my linux box (I worked flawlessly before), And
> after a reboot i get the following errors at disk detection.
>
> Is this the filesystem or the HD?
>
> NB : I had loaded just before the last rockbox w/ load. fonts, which
> wasn't showing the logo, so I tried to reset it to restore contrast
> settings
>
> Thx for your advice
> Lucas
> ---
>
> hub.c: USB new device connect on bus1/1, assigned device number 2
> usb.c: USB device 2 (vend/prod 0x4b8/0x10b) is not claimed by any active
> driver.
> hub.c: USB new device connect on bus1/2, assigned device number 3
> usb.c: USB device 3 (vend/prod 0x3f0/0x1504) is not claimed by any
> active driver.
> hub.c: USB new device connect on bus2/1, assigned device number 2
> usb.c: USB device 2 (vend/prod 0x5ab/0x60) is not claimed by any active
> driver.
> usb.c: registered new driver usblp
> usb.c: registered new driver usbscanner
> printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2
> vid 0x03F0 pid 0x1504
> printer.c: v0.11: USB Printer Device Class driver
> scanner.c: probe_scanner: User specified USB scanner -- Vendor:Product -
> 4b8:10b
> scanner.c: probe_scanner: User specified USB scanner -- Vendor:Product -
> 4b8:10b
> scanner.c: 0.4.6:USB Scanner Driver
> SCSI subsystem driver Revision: 1.00
> Initializing USB Mass Storage driver...
> usb.c: registered new driver usb-storage
> scanner.c: probe_scanner: User specified USB scanner -- Vendor:Product -
> 4b8:10b
> scsi0 : SCSI emulation for USB Mass Storage devices
> usb-uhci.c: interrupt, status 3, frame# 918
> Vendor: FUJITSU Model: MHN2200AT Rev: 7257
> Type: Direct-Access ANSI SCSI revision: 02
> WARNING: USB Mass Storage data integrity not assured
> USB Mass Storage device found at 2
> USB Mass Storage support registered.
> Adding Swap: 257032k swap-space (priority -1)
> Adding Swap: 401584k swap-space (priority -2)
> EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,5), internal journal
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
> /dev/scsi/host0/bus0/target0/lun0:scsi0: ERROR on channel 0, id 0, lun
> 0, CDB: Read (10) 00 00 00 00 00 00 00 08 00
> Current sd08:00: sense key Medium Error
> Additional sense indicates Unrecovered read error
> I/O error: dev 08:00, sector 0
> scsi0: ERROR on channel 0, id 0, lun 0, CDB: Read (10) 00 00 00 00 00 00
> 00 08 00
> Current sd08:00: sense key Medium Error
> Additional sense indicates Unrecovered read error
> I/O error: dev 08:00, sector 0
> unable to read partition table
>
>



Page was last modified "Jan 10 2012" The Rockbox Crew
aaa