Warning, the internal storage is not working so you must install Rockbox on a microsd card !!
|| LCD is working. Still lacking lcd sleep, and inversion.
|| Physical keys are handled. Touchscreen driver has been implemented.
| Music playback
|| Everything works.
| FM Radio
|| We don't have a DRI driver so we FM doesn't work.
|| Not implemented.
| Power Management
|| Everything works.
|| DMA works
|| SSP works
|| NAND driver and FTL are not implemented so no internal storage.
|| SD works.
|| Everything works.
|| Everything is implemented and should work.
| Rockbox Utility
|| Most of the code has been written but we need to put pieces together. Upgrade the bootloader is a bit tricky.
The bootloader comes with a number of features which allow to recover from potential problematic situations.
Booting to the OF
The bootloader can either boot rockbox or the OF. By default it will boot rockbox. The bootloader will boot the OF if menu
is hold while powering up (the big button below the screen). This works independently
from the power source. For example, the following actions will boot the OF:
- unplug USB cable, hold menu - then press power for a few seconds
Booting to the OF while the USB cable is plugged is possible but very tricky, here is the procedure:
- unplug cable, power down
- put your hand on menu but don't press it
- plug USB cable
- wait for a small amount of time (typical is 0.5 second)
- press menu
The timing is critical, if you press menu too early, recovery mode is entered (black screen) but if you press it too late, rockbox bootloader is entered ! You'll have to repeat many times before success.
Building the bootloader
The bootloader can be built using three different methods. The recommend one is the automatic method using RockboxUtility
. The semi-automatic method requires a working cross-compiler and a copy of the Rockbox source code.
Linux + Windows
This method requires the following things:
- a working cross-compiler (arm-elf-eabi), see HowToCompile
- a copy of the source code, see HowToCompile
- a copy of the latest firmware installer for the Creative Zen X-Fi2,
First you need to compile the bootloader, to do this follow the instructions from HowToCompile
and when running the configure script, select the Creative Zen X-Fi2 and bootloader build. After the build, you should get a
file (you don't need to go further than the 5. Build step in HowToCompile
Then you need to build the mkimxboot tool in
. To do so, just cd into
. It should produce a
Finally, you need to run the tool with the correct parameters. Assuming you are in
=./mkimxboot -i creative-installer.exe -b bootloader-zenxfi2.creative -o firmware.sb -t dualboot -v zenxfi2-sd =
You should replace
by the path to the firmwareinstaller you downloaded from Creative (like
), and replace
by the path to the
file produced by the compilation.
This is where you need windows: put the
file produced somewhere available for Windows. Reboot to Windows (or use another computer). Put
in the same directory
as the Creative installer (something called
). Now run the installer and do a normal firmware upgrade: the installer will use the
file you put instead of the standard one ! Note that you can use a virtual machine with Windows on it for this step. If you already have rockbox installed, you will need to enter recovery mode or the OF to successfully upgrade.
Of course, to run rockbox, you will also need to do a normal build of rockbox and put rockbox on your device (see HowToCompile
but this time to a normal Creative Zen-X-Fi2 build and go until the 6. Install step). Alternatively, you can download the latest build here:
If for any reason your device doesn't work anymore (doesn't boot, stuck in the bootloader and even the OF doesn't work or if a firmware upgrade failed). You might need to recover your device. You should not attempt this without an advice from someone knowledgeable. The point of the recovery procedure is too reinstall the OF and will remove any trace of the rockbox bootloader.
- 15 Jan 2013
Copyright © by the contributing authors.