release
dev builds
extras
themes manual
wiki
device status forums
mailing lists
IRC bugs
patches
dev guide



Search | Go
Wiki > Main > OtherTargets > GoGearHDD6330

Philips GoGear HDD16x0 & HDD63x0 Series


Introduction

The Philips GoGear HDD16x0 and HDD63x0 series of DAPs are different devices internally (except SoC and the codec). The HDD16x0 has a 6GB microdrive and a 128x128x16 LCD, whereas the HDD63x0 has a 30GB 1.8" hard drive and a 220x176x16 LCD. The touchpad is also different between the two. There are three known models of the HDD16x0 series: the HDD1630, the HDD1620, and the HDD1635. The major differences between the HDD1620 and HDD1630 is the inclusion of an FM radio tuner on the HDD1630. Little information is known about the HDD1635. There is also HDD1420 (4GB, without radio) and the HDD1830 (8GB, with radio).

Mark Arigo committed code for the HDD1630 to SVN on 2008-06-27, and additional code to branch the HDD6330 off into its own port on 2009-12-25.


Port Status

  • Dual boot functionality is implemented; press the MENU button (or Vol+ for HDD63X0) while booting to boot into the OF.
  • Audio playback and most core functionality is working.
  • Both devices have full use of the touchpad and all buttons.
  • Plugins are enabled on both devices.
Here is what's needed for both ports:
  • Manual
  • Battery readings are not very accurate for the HDD16X0 series.


Issues

HDD63X0:

If your HDD63X0 doesn't want to play audio under OF, or is almost unresponsive in Rockbox (doesn't want to play audio too), you had to hit the hardware bug, which is associated with switching the I2C bus to the cradle, when you plug the cable. This bug can only be triggered in OF, by just plugging the plug to the player and then unplugging it. You don't have to be connected to the PC.

Technical notes: OF sets the GPO32 - bit 0x10 after plugging the plug (switches I2C to the cradle, U515), and unsets it after unplugging, but it doesn't help. The I2C bus hangs till the real powering off, by the 8th bit of Port_B. A reset with headphones plugged in helps too somehow (note that this doesn't reset the player really, more this turns off it), probably it causes cut-off voltage of the system, like in case of Port_B.

In summary, all you can do about it is to reset the player with the headphones connected, or wait patiently until Rockbox will turn off normally (hold the power button and wait).


PCB Scans


Firmware


Hardware

  • Synaptics
    • T1005G 0538
    • ACP5060-13

  • SST39WF400A "Silicon Storage Technology, Inc. :: 4 Mbit (x16) Multi-Purpose Flash"

  • RAM
    • HDD1630: 32M - Samsung K4S56163PF or Hynix HY5V56F or equivalent (4M X 16bit X 4 banks)
    • HDD6330: 64M - Samsung K4S51163PF or equivalent (8M X 16bit X 4 banks mobile SDRAM)

  • LCD
    • HDD1630: 1.5" 128x128
    • HDD6330: 1.9" 220x176 - LPH-9165-2

  • LCD Controller
    • HDD1630: Leadis Technology LDS176 (132x132 4k) or LDS186 (128x160 64k) (based on the registers found in the OF disassembly).

  • TV OUT : ADV7179

  • Audio : WM8731L

  • Tuner : TEA5767HN

  • HD connector has the markings "PWA-ARIZONA_HDD_FPC_EMI" on the ribbon cable
    ("Arizona" is the code name of the HDD6330. "Phoenix" is the code name of the HDD1630.)

UMS Mode

This trick will allow you to connect either the HDD16x0 or HDD63x0 to your computer as a UMS device.

  • Connect the player to the PC.
  • On the player, press and hold "Power On" & "Vol +" until the unit resets.
  • Quickly press and hold "Vol -" until the PC picks up the unit and shows it as removable drive.

Installation steps for HDD63x0

We recommend using Rockbox Utility to install Rockbox on the HDD63x0 series. The following steps are for those who wish to install Rockbox manually.

  • Boot the GoGear into UMS mode as descibed above. This makes the device show up as a Mass Storage Device when attached to your PC.

  • Extract the rockbox-gogearhdd6330.zip file onto the root of your player, this creates a .rockbox folder on the device.

  • On the GoGear, rename /System/FWimage.ebn to OF.ebn and copy the FWImage.ebn you downloaded from the above link into the /System folder on your GoGear.

  • Disconnect your device from your computer. It should reboot and launch Rockbox.

Installation steps for HDD16x0

We recommend using Rockbox Utility to install Rockbox on the HDD16x0 series. The following steps are for those who wish to install Rockbox manually.

  • Boot the GoGear into UMS mode as descibed above. This makes the device show up as a Mass Storage Device when attached to your PC.

  • Download and extract a build to your player: http://build.rockbox.org/data/rockbox-gogearhdd1630.zip

  • Download the bootloader: http://download.rockbox.org/bootloader/gogear/hdd1630/FWImage.ebn

  • Extract the rockbox-gogearhdd1630.zip onto the root of your player, this creates a .rockbox folder on the device.

  • On the GoGear, rename /System/FWimage.ebn to OF.ebn and copy the FWImage.ebn you downloaded from the above link into the /System folder on your GoGear.

  • Disconnect your device from your computer. It should reboot and launch Rockbox.


CategoryFrontpage: Philips GoGear HDD16X0/63X0 Port Index [New Ports]
I Attachment Action Size Date Who Comment
PHILIPS_HDD1420_ServiceManual.pdfpdf PHILIPS_HDD1420_ServiceManual.pdf manage 1576.4 K 13 Nov 2008 - 00:03 AntonVeretenenko HDD1620/HDD1420 Service Manual (with schematics)
Philips_HDD6320_HDD6330_Service_Manual.pdfpdf Philips_HDD6320_HDD6330_Service_Manual.pdf manage 1238.2 K 25 Feb 2010 - 10:09 SzymonDziok HDD6320/HDD6330 Service Manual (with schematics)
lds176_spec.pdfpdf lds176_spec.pdf manage 2275.3 K 20 Jan 2009 - 15:56 MarkArigo  
r40 - 12 Nov 2014 - 11:58:50 - SzymonDziok

Parents: OtherTargets
Copyright by the contributing authors.