release
dev builds
extras
themes manual
wiki
device status forums
mailing lists
IRC bugs
patches
dev guide



Search | Go
Wiki > Main > MioC510 (r3)

Mio C510 / C710


Overview

This is the page for the Mio C510 and C710 devices.

Hardware

The Mio C510 and C710 are GPS/DPA devices running WinCE? .NET 4.2. They features 4 hardware buttons (power, menu, volume up/down), a reset button, an on/off power switch and a touchscreen. They also features a speaker. The following chips can be found on the PCB:
  • W68136:3V SINGLE-CHANNEL 13-BIT LINEAR VOICE-BAND CODEC
  • VP1020-N: Voice Processor
  • WM8976: Stereo CODEC With Speaker Driver
  • LC4064ZC?-75MN6: 3.3V/2.5V/1.8V In-System Programmable SuperFAST? TM High Density PLDs
  • GSC3f-7879: SirF? Star III
  • K4M561633G?: DRAM
  • K9F4G08U0??: Flash
  • B6150H1?: BRF6150 bluetooth v1.2 compliant
  • 922Z: ISL6292 Li-ion/Li Polymer Battery Charger
  • 68TI: LTC3411EMS? ?
  • 4855: FAN4855 500mA High Efficiency Boost Regulator with Adjustable Output, Shutdown and Low Battery Detect
  • S3C2440L?-40: Samsung S3C2440? SoC
  • GNS GmbH?: TMC receiver ? (only C710)

Recovery mode

The Mio C510 and C710 feature a recovery mode accessible by hard powering down the device and then powering up holding the volume down button. It has several menus to update uboot or wince. The bootloader can be safely overwritten using the WinCE? SD/MMC update. It is also possible to boot WinCE? by holding menu and volume up.

PCB Scans

Pins

Here is a list of all the pins used by the OF. Direction only applies to GPIO.
Pin Dir*/*Function Component Comment
GPB9 output Battery  
GPC9 output BTHCI Chip Enable / Reset
GPE12 input   Jack detect
GPF0 input / EINT[0] Button Power button
GPF2 input / EINT[2] Button Reset button
GPF7 input / EINT[7]   SD detect
GPG1 input Battery USB present
GPG2 output BTHCI Chip Enable
GPG3 input   Menu key
GPG4 input   Volume plus key
GPG5 input   Volume down key
GPG8 input Battery  
GPG9 input Battery Battery charging ?
GPG10 input Battery  
GPG11 output Battery Charging led color
GPH0 nCTS0 BTSer UART[0] CTS
GPH1 nRTS0 BTSer UART[0] RTS
GPH2 TXD[0] BTSer UART[0] TX
GPH3 RXD[0] BTSer UART[0] RX
GPH4 TXD[1] GPS UART[1] TX
GPH5 RDX[1] GPS UART[1] TX
GPH6 output BTSer UART[0] DTR
GPH7 input? BTSer UART[0] DSR
GPH10 CLKOUT1 BTHCI External clock
GPJ0 output GPS  
GPJ7 output GPS Chip Enable/Power ?
GPJ8 output GPS  
GPJ10 output GPS  
GPJ12 output GPS  

-- AmauryPouly - 21 Jun 2012
Edit | Attach | Print version | History: r4 < r3 < r2 < r1 | Backlinks | View wiki text | More topic actions...
r3 - 21 Jun 2012 - 22:36:10 - AmauryPouly
Copyright by the contributing authors.