Downloads
release
dev builds
extras
themes
Documentation
manual
wiki
device status
Support
forums
mailing lists
IRC
Development
bugs
patches
dev guide
Search



Donate

Wiki > Main > CreativeZenV (compare)

Difference: CreativeZenV (r8 vs. r7)

Creative Zen V (Plus) Port


Intro

Small flash based player from Creative. The V Plus models have a radio and can play video.


Creative's Software Recovery Mode

  • Detach your player from the PC if it is connected, and turn off the player. (If the player stops responding, you can reset the player. To reset the player, gently insert a thin object into the Reset hole located below the power switch.)
  • Press and hold the Play button while powering on your player.
  • When the player displays the Creative logo, release the Play button.

It will display the following options

  • Clean Up: Scans the player and removes invalid links from its music library. Does not affect music files themselves.
  • Format (All): Caution! Erases all content! Save a copy of your player's content before formatting.
  • Reload OS/ Firmware: Caution! Erases your player's firmware. DO NOT select the Reload Firmware option unless you have access to a PC and you have downloaded the necessary firmware to install.
  • Reboot: Reboots the device.


SigmaTel's Hardware Recovery Mode

Like the other STMP3xxx players, the Zen V has a built-in hardware recovery mode which presents itself as a Player Recovery Device Class with the proper drivers installed. Normally this mode can be accessed by holding a button while connecting to USB, but I tried many different combinations and couldn't find one. Then, after reading a ton of forum posts about the recovery mode showing itself after people screwed up their batteries, I thought I'd try simply removing it and it did indeed connect in recovery mode. Perhaps there is another way, and in the meantime we have no use for this, but now we know how to get to it if required.


Hardware

ZenV_SOC.pngCreative CA0209-HA6 - Apparently Re-branded a re-branded STMP3600 according to some STMP3600 reports
ZenV_Flash2.png Samsung K9L8G08U0M? - NAND - Datasheet
Philips TEA5767 - FM Radio - Data sheet
Phison PS3002T? - CompactMedia Controller - Data sheet
Infineon HYB25L25616AF? - SDRAM - Data sheet
SSD1338U2? - LCD IC - This similar LCD used to use the same controller.
This guy wrote a device driver for SigmaTel.
This could prove handy.
http://www.solomon-systech.com/pdf/OLED%20into%20mobile%20main%20display.pdf


Memory registers

LCD interface (all uint32)
HW_LCDIF_CTRL_ADDR 0xF0060000
HW_LCDIF_CTRL_SET_ADDR 0xF0060004
HW_LCDIF_CTRL_CLR_ADDR 0xF0060008
HW_LCDIF_CTRL_TOG_ADDR 0xF006000C
HW_LCDIF_TIMING_ADDR 0xF0060010
HW_LCDIF_DATA_ADDR 0xF0060020
HW_LCDIF_DEBUG_ADDR 0xF0060030

(see linuxbsp-stmp36xx-kernel-20060601-375.tar.gz\kernel2.6.16\linux-2.6\include\asm-arm\arch-stmp36xx\regslcdif.h for more info)


lsusb Output on Hardware Recovery Mode 

Bus 001 Device 005: ID 066f:3600 SigmaTel, Inc. 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x066f SigmaTel, Inc.
  idProduct          0x3600 
  bcdDevice            0.01
  iManufacturer           1 Sigmatel, Inc.
  iProduct                2 STMP3600
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          3 USB Boot Class-c
    bmAttributes         0xc0
      Self Powered
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0 
      bInterfaceProtocol    255 
      iInterface              4 USB Boot Class-i
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0


Useful Links

View topic | View difference side by side | History: r13 < r12 < r11 < r10 | More topic actions
r13 - 20 Apr 2013 - 16:17:27 - AmauryPouly

Revision r8 - 20 Sep 2008 - 15:08 - MarcGuay
Revision r7 - 20 Sep 2008 - 00:51 - MarcGuay
Copyright © by the contributing authors.