IriverNavigation

Function Memory Mapping

Function Address info

Can we agree on a common firmware to analyze? I suggest the US firmware? But should it be 1.40 or 1.60?

I'm just making up descriptive function names. -- PaulS?

StephanNielsen: I was wondering which tools and methods you use to analyze the firmware (extract addresses). Disassembler (objdump), A modded MCF5249 emulator, BDM, GDB??? Is it possible that you could inform other interested people about this on a separate WikiPage? - unless of course you will rather do all the hard work yourself ;). Have anyone been able to compile a cross-compiler for the MFC5249 yet - a WikiPage? for instruction on how to do this would also be really useful? PaulS?: Check out the new addition to the ColdFire page.

PaulS?: There's not a lot of magic going on here. I think there are other people (and pages) that are much better suited to give a tutorial on disassembly. The tools I've relied on the most are the disassembly tools I mentioned on the IriverPort page. I wrote a little perl code to build forward and reverse function call trees, but the results of that haven't been very useful so far. Aside from that, I spent a little time getting used to the assembly language, kept a ColdFire Programmers Reference Manual and the CF5259 User Manual by my side and curled up with some code. It didn't take long to get an intuition for loop structure and function call semantics. The important bit of code I found very early on built the Software Memory Map below, which talks about where all the peripheral interfaces are in memory. Just searching for references to the GPIO memory range (mostly in MBAR2) will get you plenty of interesting code to look at and ponder on what it's doing. Again, other people might be better at formalizing this process. Is this short bit worth a separate Wiki page?

StephanNielsen: Ok, fair enough. I will make an IriverToolsGuide WikiPage then, but please forgive me for making mistakes cause inspite of your description, I am still in doubt about a few things.

Function Name	Address	Firmware Version
Display function	SDRAM 0x31045050	1.40US
draw_string(char *, int, int, int) (draws text at the bottom center)	0x31053408	1.40US
status_message(char *)	0x31053BF4	1.40US
memcpy()? Code is in SRAM for speed.	0x10000400	1.40US
ADC_read(int mux_channel)	0x310604C0	1.40US
keystroke_decode(int adc_value)	0x310609A8	1.40US
get_keystroke()	0x3106104C	1.40US
debug_puts(char *) (disabled)	0x3102CC68	1.40US
debug_print(int) (disabled)	0x3102CC70	1.40US
putc(char) (serial port)	0x3102CBE0	1.40US
repaint_display()	0x3104C51C	1.40US
mbus_select()	0x3102F47C	1.40US
i2c_write()	0x3102E848	1.40US
flash_upgrade_file_exists()	0x3103EF94	1.40US
set_drive_state()	0x31035DD4	1.40US
get_drive_state()	0x31035E20	1.40US
wake_drive()	0x3105577C	1.40US
ide_read_sector()	0x31030318	1.40US
read_file_into_memory()	0x31033538	1.40US
firmware_into_ram()	0x3103EEC8	1.40US
firmware_load_and_decode()	0x3102284C	1.40US
program_new_firmware()	0x31022A04	1.40US
render_General_menu(int ent_no)	0x31049C84	1.40US
sel_General_menu() (conditionally calls fw funcs)	0x31068A38	1.40US
is_flash(char *) - compares string to "IHP_120 HEX"	0x3103B9EC	1.40US
scan_dir() calls is_flash() for each dirent; stores file handle on success	3103C3B0	1.40US

Software Memory Map

The iRiver can map external peripherals in a flexible manner, using the Chip Select Module. There are also base address registers for many other facilities so devices like GPIO registers can float around based on the firmware in question. Here's an attempt to document the 1.40US firmware's setup (and coincidentally the 1.60 appears largely the same) for various important bits. Some of these registers are supervisory registers in the core, accessed by special MOVE instructions. Others, like the chip select regs are actually within the MBAR.

Register Name	Address Range	Description	Contents
MBAR	0x40000000	Module Base Address Register 1	System Control, Interrupt, Chip Select, Timer, SDRAM and UART regs
MBAR2	0x80000000	Module Base Address Register 2	GPIO data and control registers
RAMBAR0	0x10010000	SRAM Base Address Register 0	Base address for the first SRAM segment
RAMBAR1	0x10000000	SRAM Base Address Register 1	Base address of the second SRAM segment
VBR	0x10000000	Vector Base Register	Lives in SRAM
CS0	0x00000000-0x001FFFFF	Chip Select 0	ROM address -- Defaults to 0x0 at boot time as well, Control Reg = 0x00000D80
CS1/GPIO1	0xF0000000 - 0xF3FFFFFF	Chip Select 1	Connected to the main LCD display chip, Control Reg = 0x00002140
CS2/IDE	0x20000000 - 0x200FFFFF	Chip Select 2	Setup for integrated IDE controller, Control Reg = 0x00000168
SDRAM	0x31000000 - 0x310FFFFF	External SDRAM	DCR=0x8040, DACR0 = 0x31002520, DMR = 0x03FC0001

GPIO Signals

Here's a summary of how the ColdFire GPIO pins are used on the iRiver. These are mostly guesses that LinusNielsenFeltzing should be able to confirm or dispute based on his findings. The I/O/F column indicates whether the pin is a GPIO Input, GPIO Output or Function pin (assigned to the ColdFire's special-purpose function, or not used). Pointers are into the 1.40US SDRAM code.

"*" indicates that this GPIO or function is actually implemented by two pins on the physical package -- one dedicated input pin and one dedicated output. This means that this logical bit can serve two functions simultaneously. There's only one bit that decides function vs. GPIO, so the composite pin must either both be function pins or a GPI and GPO pin.

"(C)" indicates that it is confirmed

DaveHooper: Is the battery LED connected to GPIO or is it controller directly by the charging hardware?

Hardware Address info

A lot of documentation can be found in the ColdFire manuals. The below list refers to the most important address tables:

Exception Vectors (page 98)