Mio C510 / C710
Overview
This is the page for the Mio C510 and C710 devices.
Hardware
The Mio C510 and C710 are GPS/DPA devices running WinCE? .NET 4.2. They features 4 hardware buttons (power, menu, volume up/down), a reset button, an on/off power switch and a touchscreen. They also features a speaker. The following chips can be found on the PCB:
- W68136:3V SINGLE-CHANNEL 13-BIT LINEAR VOICE-BAND CODEC
- VP1020-N: Voice Processor
- WM8976: Stereo CODEC With Speaker Driver
- LC4064ZC?-75MN6: 3.3V/2.5V/1.8V In-System Programmable SuperFAST? TM High Density PLDs
- GSC3f-7879: SirF? Star III
- K4M561633G?: DRAM
- K9F4G08U0??: Flash
- B6150H1?: BRF6150 bluetooth v1.2 compliant
- 922Z: ISL6292 Li-ion/Li Polymer Battery Charger
- 68TI: LTC3411EMS? ?
- 4855: FAN4855 500mA High Efficiency Boost Regulator with Adjustable Output, Shutdown and Low Battery Detect
- S3C2440L?-40: Samsung S3C2440? SoC
- GNS GmbH?: TMC receiver ? (only C710)
Recovery mode
The Mio C510 and C710 feature a recovery mode accessible by hard powering down the device and then powering up holding the volume down button. It has several menus to update uboot or wince. The bootloader can be safely overwritten using the WinCE? SD/MMC update. It is also possible to boot WinCE? by holding menu and volume up.
PCB Scans
Pins
Here is a list of all the pins used by the OF. Direction only applies to GPIO.
| Pin | Dir*/*Function | Component | Comment |
|---|
| GPB9 | output | Battery | |
| GPG1 GPC9 | input output | Battery BTHCI | Charge source present ? Chip Enable / Reset |
| GPG8 GPE12 | input | Battery | Jack detect |
| GPG9 GPF0 | input / EINT[0] | Battery Button | Battery charging Power button ? |
| GPG10 GPF2 | input / EINT[2] | Battery Button | Reset button |
| GPG11 GPF7 | output input / EINT[7] | Battery | Charging led SD detect color |
| GPH0 GPG1 | nCTS0 input | Bluetooth Battery | UART[0] CTS USB present |
| GPH1 GPG2 | nRTS0 output | Bluetooth BTHCI | UART[0] RTS Chip Enable |
| GPH2 GPG3 | TXD[0] input | Bluetooth | UART[0] TX Menu key |
| GPH3 GPG4 | RXD[0] input | Bluetooth | UART[0] RX Volume plus key |
| GPG5 | input | | Volume down key |
| GPG8 | input | Battery | |
| GPG9 | input | Battery | Battery charging ? |
| GPG10 | input | Battery | |
| GPG11 | output | Battery | Charging led color |
| GPH0 | nCTS0 | BTSer | UART[0] CTS |
| GPH1 | nRTS0 | BTSer | UART[0] RTS |
| GPH2 | TXD[0] | BTSer | UART[0] TX |
| GPH3 | RXD[0] | BTSer | UART[0] RX |
| GPH4 | TXD[1] | GPS | UART[1] TX |
| GPH5 | RDX[1] | GPS | UART[1] TX |
| GPH6 | output | BTSer | UART[0] DTR |
| GPH7 | input? | BTSer | UART[0] DSR |
| GPH10 | CLKOUT1 | BTHCI | External clock |
| GPJ0 | output | GPS | |
| GPJ7 | output | GPS | Chip Enable/Power ? |
| GPJ8 | output | GPS | |
| GPJ10 | output | GPS | |
| GPJ12 | output | GPS | |
-- AmauryPouly - 21 Jun 2012
Copyright © by the contributing authors.
