From: Peter Nome <peter_at_cogweb.net>
Date: Mon, 20 Jan 2003 16:32:55 -0800

As I thought, compiling in support for scsi disks solved the problem I had mounting
the device. The 2.4.20 kernel gives lots of information when it boots the Archos,
attached below. I'm getting Bad target number and an apparently failed "Attempting
to get CSW" -- any ideas what's going on? What I actually DON'T get is a nice little
message telling me where the device is, as on Bjorn's page -- "Detected scsi disk
sda at scsi1, channel 0, id 0, lun 0"... But mounting /dev/sda1 works:

Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
 sda:<7>usb-storage: queuecommand() called
 sda1

Cool!

Peter

Here's the new dmesg, in case anybody cares:

SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 88
usb-storage: Array length appears to be: 90
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xc15c5794 Out: 0xc15c5780 Int: 0xc15c57a8 (Period 9)
usb-storage: New GUID 05ab0060fffffffffff7d96a
usb-storage: GetMaxLUN command result is -32, data is 128
usb-storage: clearing endpoint halt for pipe 0x80000280
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 5b df ac e0 ed de
usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 36/255
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0010280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x1 R 219 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
  Vendor: HITACHI_ Model: DK23DA-20 Rev: 00J2
  Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7/0)
usb-storage: *** thread sleeping.
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Received on 2003-01-21