On my X3, it triggers the MIPS equivalent of a segfault. (directory has 792 entries, tried to access it with only 500 allowed)

Rather than crashing outright, I think it would be better to detect this and somehow error out gracefully?

Playing APE 24/44.1 with harsh noise in different parts of the track. If you decode APE file to WAV using the codec console, then there are no problems. So the matter is in the player’s APE decoder.

At 24/48 everything is fine.

I use a 64 GB MicroSD card in my Clip Zip and the stock firmware recognizes it. Rockbox recognizes it in the debug disk info screen and when connected to a computer via USB, I can read and write it through rockbox. However, when I try to access it or when I just check the regular rockbox info, rockbox does not show the SD card, nor can I play music from it.

The bug is also present in the current development version and is overall very similar to this one: https://www.rockbox.org/tracker/11798

I tried reinstalling rockbox and reformatting the SD card, but nothing worked.

I store the album art by putting a folder.jpg file in the album's directory.
Any WPS on other players shows the cover pictures properly if album art is enabled in the theme.

I am aware of caveats like progressive jpgs, that are not supported by RB.

In the attached zip file, there are four directories with a folder.jpg file and a free opus file for demonstration purposes.

All pictures show up fine on my Sansa E200 (v1) using CabbieV2 or lebellium_Samsung-like.
However, on my XduOO x3ii the pictures are not displayed for the examples 1 - 3, but show for example 4.

None of the jpgs are progressive and I cannot figure out a difference between 1-3 and 4.

I don't know how to debug this further myself, but would be happy doing any furter experiments.

This is true for the current dev builds, e.g. b450707955.

Playing 320K MP3s pauses often in Version 3.15 and daily build 7d00533 also UI becomes unresponsive
Version 3.14 or older does not reproduce the issue in either 44 or 48khz sampling rate and same sound options
Is not reproducible under OF or Version 3.15 running on IPOD 6G
seems to be a cpu usage issue as compiling a version of rockbox with much higher than stock CPU clocks seems to alleviate the issue to an extent but there is still occasional pauses that is not present after reverting to 3.14 and stock 80 mhz clock speed.

I am trying to build Rockbox for Sony NWZ-380 from Git repo, commit ce0b31d87db3c4c1c1bfb535c50770d33e9c4aaf.
arm-elf-eabi-gcc version 5.4.0, ARM binutils 2.30.
Everything goes smooth until just the latest step where this happens:

… LD duke3d.ovl
LD bmp.ovl
LD jpeg.ovl
LD png.ovl
LD ppm.ovl
LD gif.ovl
LD rockbox.elf
/usr/libexec/gcc/arm-elf-eabi/ld: section .ARM.exidx VMA [00000000600a9548,00000000600a954f] overlaps section .bss VMA [00000000600a7f20,00000000600ff773]

I'm using Rockbox on my NWZ-384 for a couple of years now and there were no problems building it in the past. I also was very glad that NWZ-380 port reached stable status in 3.14,
but now something seems to be broken (not terrible it seems, just requires some adjustments to the linker scripts but still).

I have an upgraded iPod 5.5 with CF 32Gb installed in CF-ZIF adapter.
Both iTunes & Rockbox are working fine with this setup.

Then I tried to increase the storage space by using mSata SSD 64 GB + mSata-ZIF adapter. iTunes recovered the iPod successfully and it is working just fine. I installed Rockbox latest stable (non-stable latest = same thing) version & after the Rockbox boot-up it reporting an ATA error -11.

I wonder if this can be solved.

Thanks!

I recognize some problem with USB support.

When I’m connecting my player first time, it’s work correct - computer’s mounting device propertly. BUT When I disconnecting it, turn on playing and while music is still playing I’m connecting player once more - Rockbox is crashing and give information about “unidentified instruction at… “. Now player looks like dead - I must reset it and Rockbox start correctly.
When I’m not turning on songs - all works fine.

Sorry for my english…I’m still learining It

Pure i20 does not charge the iPod classic with OS rockbox.
I feel like Rockbox can not recognize interface pure i20 (drivers?)
Through Pure i20 will not play music even if it is in the installed Rockbox in the iPod.(only apple Flash = possible charging/playing via Pure i20)

I own Ipod classic 6G 160GB (flashed rockbox)

Creative ZEN
Daily build: rockbox-creativezen-20170112

Bug description:
When plugging any dummy plastic or a non supported SD card, the device freezes and displays a white screen with a “PANIC” error message.
Plugging a standard SD card works fine.
To restore the system, you have to use a paper clip to do a hardware reset and turn the device on again.

Trying to cross-compile GCC for the ipod with GCC 9.2 I keep running into errors:

In file included from ../../gcc-4.4.4/gcc/diagnostic.h:25,

               from ../../gcc-4.4.4/gcc/tree-mudflap.c:43:

../../gcc-4.4.4/gcc/pretty-print.h: At top level:
../../gcc-4.4.4/gcc/pretty-print.h:310:6: error: ‘cgraph_node’ is not defined as a type

310 |      ATTRIBUTE_GCC_PPDIAG(2,3);
    |      ^~~~~~~~~~~~~~~~~~~~

This would seem to be the same issue as the one described on https://gcc.gnu.org/bugzilla/show_bug.cgi?id=90677

The attached patch against GCC seems to fix the problem for me.

I’m using the latest Dev build for the Fuze+. SanDisk Sansa Fuze+ 5ef1e2d. Same issues experienced in v3.12 stable.

The screen, for lack of a better term, jumps when navigating in upside-down mode.

http://youtu.be/dRfiBtMx2to

This bug is sporatic “the worst kind”, has effected a 4gb fuze+ “foolsh in IRC” and an 8gb fuze+ “DmL in IRC“, but also has been confirmed to be absent from one other 4gb fuze+

Rockboy data aborts on menu key press, when the srceen is rotated left and image is stretched across the whole srceen. Also no matter what key is mapped to the menu entry it will still fail.

It never fails when aspect ratio is maintained with scale or when not scaled at all, and never aborts when rotated right or not at all.

Only four files even mention rotate in the apps/plugins/rockboy/ directory “lcd.c menu.c rockmacros.h and sys_rockbox.c”

Sometimes the failure does not happen and reaching the menu is possible, but the rockboy option file may get written and not allow the user back into the menu later to change the rotate option back. When this happens the option file must be edited or erased to make rockboy work again normally.

Neither of the tools, ipodpatcher or Rockbox Utility 1.4.0, work on macOS Catalina.

Catalina removed 32bit support.

Using ipodpatcher generates the following error:

bash-3.2$ ./ipodpatcher
bash: ./ipodpatcher: Bad CPU type in executable

And Rockbox Utility has a white circle with a line through it indicating that it does not work with this version of the OS.

(see attached file)

I primarily use my unit for audio books while driving, but the latest build (as I write this) won't play one of the files properly. It tries to start, stuck at 0:00. Trying to seek hangs the player altogether, requiring a hard restart.

I've recreated this problem on a flaky Clip+ and an AGPTek Rocker.

The 'file' tool identifies it as: ISO Media, MP4 v2 [ISO 14496-14]

Here's what mplayer has to say (while playing it back properly):

[lavf] stream 0: audio (aac), -aid 0, -alang eng

Hello there,

When I reboot my Rockboxed iPod nano second generation, it changes the time +5 hours.

Does anyone know why this can be? Thanks

Back button does not work, and sometimes the same function as the forward button.
Rewind button does not work
Of course, I am talking about are the physical buttons，Touch buttons are working properly。

Reported Version: 3.15 not 3.14

Hello,

I am using a "SanDisk Sansa Clip+" and it seems that currently it is not possible to remove quickscreen entries when they are set, you can only overwrite them.

In the manual chapter "3.15 Quick Screen" has to be adapted, once this function has been implemented.

It would be very nice to have this possibility!

-Ramon

There is an ALAC playback problem in daily builds (since 2014-11). The playback somethimes works for one song but then crashes and shows ALAC file details as "? kbit/s", "0 MHz", "0 MB" and nothing happens when I press the Play button. After reboot the problem occurs again. It makes the ALAC playback impossible.

Now I'm using revision 9cb9f76M-140326 with patches from aroldan:

https://www.dropbox.com/sh/b5xbw6cp4ikfxwn/MjELjmDNJ_

With this build there are no ALAC playback problems.

After upgrading from "Version: 33856d9-161111" to "Version: 6436c6e-170211" Resume Playback from the main menu does not work. Here are the steps taken to verify the problem:

Running Version: 6436c6e-170211… Reset config
Using default settings, enabled Shuffle via Shortcuts
Started playlist; track identified as 1 of 5330
Skipped ahead to the 5th track
Paused @ 1:01
Forced shutdown
Enabled Hold switch
Waited ~1 min., then booted via disengaging Hold switch
Clicked Resume Playback… resumed on the same first track (1 of 5330)
This behavior occurred every time I attempted to Resume Playback.

Restored previous version (Version: 33856d9-161111)
Rebooted
Reset Settings
Using default settings, enabled Shuffle via Shortcuts
Started playlist; track identified as 1 of 5330
Skipped ahead to the 5th track
Paused @ 1:01
Forced shutdown
Enabled Hold switch
Waited ~1 min., then booted via disengaging Hold switch
Clicked Resume Playback… resumed on the fifth track @ 1:01

FWIW: No Bookmarking used (never have). Database not initialized (never use it).

Hi,
I've been using the development version of Rockbox in my ipod classic 6th generation for about two years I think, but from some time, like a month or two, I'm experiencing playback issues as the track I'm listening suddenly skip forward or backward, or even jump for a few seconds on another mp3 file inside the ipod I was just listening before. I don't think is a ipod issue because I can listen the file inside the ipod with my computer player without problems.

There some way I can check older development revisions for the classic? It appears that it doesn't show in the dev build link on the site because is not fully supported. Thanks

Version 9e186e34ab-190820

i have an ipod 7th gen
rockbox installed
140.000 titles

database contains in unpredictable many cases of the folders 2 times the same title
not in all folders, but it happens very often that i open one and i see all titles 2x although they are only 1x on the sd card

the files exist only ONCE
but the database keeps listing them all 2 times

i rebuilt it several times, but the database keeps on doing that

any hint what i can do?

start as apple / itunes and delete rockbox folder / install new did not help

Creative ZEN simulator build 9d0c0e3-170115
Creative ZEN device build 8fec364f6-170125

Steps:

(Using attached config.cfg)

1 Ensure Settings > Playback Settings > Shuffle is No
2 In Files, move to a list of tracks and press Select
3 In Files, move to a different list of tracks and do long Select > Current playlist > Insert
4 View the playlist e.g. http://i.imgur.com/xR0WMQm.png 5 Set Shuffle Yes and then Shuffle No
6 View the playlist

Expected e.g. https://archive.is/41khH#selection-1007.0-1007.44 , https://archive.is/nypDH#selection-1079.0-1092.0:
Playlist order restored.

Observed: Playlist changed, but not restored - http://i.imgur.com/DBW9wSI.png

Video at https://www.youtube.com/watch?v=2_s27g_FwXg

Creative ZEN simulator build 9d0c0e3-170115
Creative ZEN device build 8fec364f6-170125

Steps:

(Asing attached config.cfg)

1 Set Settings, Playback Settings > Shuffle to Yes
2 In Files, enter a folder of tracks and press Select to play
3 Go up to the folder itself, press long select > Current playlist > Insert Last
4 Press long select > Current playlist > Insert
5 Press long select > Current playlist > Insert
6 Go to Now Playing > Current playlist > View current playlist

Expected: Four copies of the list, all shuffled

Observed: One copy of the list, shuffled, followed by three not shuffled: http://i.imgur.com/Emldcdt.png

Video at https://www.youtube.com/watch?v=KANEkz0zRZ8

I am reopening  FS#11501  - Sansa Clip v2 FLAC playback skips regularly, which was closed because a sample file was not provided. I didn't think this was necessary because I stated it happened regularly with just about any file.

I am currently on build 30217. It skipped for me last night on this track:
http://www.archive.org/download/johnbutlertrio2011-07-24.lsdII.flac16/johnbutlertrio2011-07-24_lsdII_t07.flac

I cannot attach the track to this ticket because it is larger than 2mb.

Again, it is nothing inherent in that track: a second playthrough did not skip. That 16-bit/44.1khz track was generated with FLAC 1.2.1b using normal procedures.

This problem has occurred for any build I've ever tried on a clip v2 player.

Here is my original problem statement:

Build 27566 (and all previous builds), Sansa Clip v2.

playback of 16-bit/44khz FLAC format regularly will skip ahead to next track.

in a 60 minute playback session, it'll probably happen 2-3 times. this is not due to a defect in the FLAC files. it happens with any FLAC set I attempt.

this does not happen with the Clip v1 on the same build number.

this is my first bug submitted. I searched for duplicate reports but didn't find anything.

thank you!

Create silence in Audacity program (Generate → Silence). Convert the wav file to ogg vorbis file. Put into the sansa clip+ player wav and Ogg files. Turn on the equalizer and set 32 hz, 64 hz, 125 hz in the 0.5-2.0.
Turn on maximum volume. Listen to the silence of wav file. Absolute silence. Listen Ogg Vorbis file - hear the noise (like the wind). It’s bug with only ogg vorbis. mp3, flac, mp4 is absolute silence.
On a musical files it’s additional noise. Ogg vorbis is economical of disk space. Testing on a sansa clip+ with 2GB.

Whenever screendump is enabled,It gets a panic error.
Error Message:
*PANIC*
Stkov usb
pc:080739ac sp:080f5458

The volume settings are bypassed and is at max volume when the plugin is started. Even when putting it at -60DB it still has sound. After exiting and relaunching the app,the volume is maxed again,regardless of volume settings.

I think commit 1654efc31339972d0e6bd41a499fcffc0a45822e introduces the following error:
storage_init in firmware/storage.c does not return an rc error code in case !CONFIG_STORAGE_MULTI
because its discarded here:

#else /* ndef CONFIG_STORAGE_MULTI */
+ STORAGE_FUNCTION(init)();
+#endif /* CONFIG_STORAGE_MULTI */

+ storage_thread_init();

   return 0;

Please refer to forum post for full exchange: http://forums.rockbox.org/index.php/topic,52518.0.html

In summary playing ALAC will crash the unit, other codecs not as much. My reasoning is (as contained in the forum post):

Converting some of my ALAC collection to FLAC to test has given excellent results = no crashes. I am suspicious of the ALAC decoder; watching the VIEW BUFFERING THREAD there seems to be consistency:

OGG/MP3/FLAC/WAV: CPU Frequency goes up to 124 until pcm: becomes full, then drops to 45mhz and pcm: hovers (it is always active) near the top of 100%. Upon track change the cycle starts again (124mhz until pcm: becomes full). I don't seem to get crashes.

ALAC: CPU Frequency goes up to 124 until pcm: becomes full, then drops to 45mhz and pcm: quickly goes down (takes about 2 seconds) to 75%, then cpu switches to 124mhz to get pcm: back up to 100%. This goes on constantly (cpu high - low cycle) while a single track/file is playing. I am now believing this cpu going up and down constantly gives me the crashes. Note on crashes: I don't know when they will happen, sometimes after a minute or two, sometime after 10 minutes , there is no pattern I can tell.

Ordinarily, when Rockbox is shut off and turned back on, it will remember the position in the last-played song, and begin playing from where you left off. However, in the latest build, Rockbox doesn't remember the last track that was playing if the file used a relative path. This happens on every version of 3.14 including the current daily build (2017-11-13).

Here is how the error can be reproduced:

Have a folder with two songs. Then, in the parent folder, create two m3u playlists named "absolute.m3u" and "relative.m3u".
.\
—absolute.m3u
—relative.m3u
—MUSIC\
——song1.ogg
——song2.ogg

In the absolute.m3u playlist, add the following lines:
MUSIC\song1.ogg
MUSIC\song2.ogg

In the relative.m3u playlist, add the following lines:
.\MUSIC\song1.ogg
.\MUSIC\song2.ogg

To see expected behavior:

1.) Open the files list, and run absolute.m3u and song1.ogg begins playing.
2.) Push right to start song2.ogg. Let it play a few seconds in.
3.) Turn off your device by pressing power.
4.) Turn on your device with the power button.
5.) song2.ogg continues to play the same song at the same location as when it was shut off.

To reproduce the bug:

1.) Open the files list, and run relative.m3u and song 1 begins playing.
2.) Push right to start song2.ogg. Let it play a few seconds in.
3.) Turn off your device by pressing power.
4.) Turn on your device with the power button.
5.) song1.ogg plays from the very beginning.

The file format of the songs doesn't seem to matter (I've tested ogg and mp3).

If your Ipod accessory doesn’t work with rockbox, you can report it here.

Please put your device name, Ipod model, and tested rockbox version in your post. If some but not all features work, be sure to mention that in your post.

Edit by rasher:
You should also add your results to this page page: http://www.rockbox.org/twiki/bin/view/Main/IpodAccessories

For any developers who might work on IAP support, please add patches to this task, so potential testers are notified.

I have an iPod 4G Grayscale (model A1059) running Rockbox 3.14 with an Apple FM remote (model A1187). The remote part works ok (Play/Select and Fwd/Rev buttons work - volume control is separate due to it being connected to the line out, but works).

However, the radio menu does not show up in the main menu when connected. Not when I boot with the remote connected, not when I connect it after booting, and not if I go to a different menu and then back.

In the debugging menu, it simply says that the FM tuner hardware is not found.

I am sure that this used to work at some point. Are there known regressions?

On my Sansa c250v1, the starfield plugin crashes at the address 0x01F80394 with a data abort.
It seems that the plugin is attempting to execute data.
Strangely, it does not happen in the simulator.

Click on the music file and die

When using the H300 non-lcd remote to turn on the player (iriver H340) I get the following error message “hold switch on, power off…” (the hold switch is not on).

Rockboxutility barfs while creating talk files if it encounters unpronouncable charicters (japanese kanji) and does not continue afterwords resulting in talk files not being copied to the player.

[talkgenerator.cpp:156 INFO] voicing: "シマシマ" to "/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.wav"
[ttsfestival.cpp:188 INFO] Voicing "シマシマ" → "/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.wav"
[rbsettings.cpp:162 INFO] GET U: "festival-client/path" "/usr/bin/festival_client"
[ttsfestival.cpp:194 INFO] Client cmd: "/usr/bin/festival_client –server localhost –otype riff –ttw –withlisp –output \"/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.wav\" –prolog \"/tmp/RockboxUtility.zowYwG\" - "
[:0 WARNING] QProcess: Destroyed while process ("/usr/bin/festival_client") is still running.

/
The result of this is an invalid wav file wich the the encoder bails out on and the process aborts.

[talkgenerator.cpp:235 INFO] encoding "/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.wav" to "/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.talk"
[encoderrbspeex.cpp:82 INFO] Encoding "/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.wav" to "/tmp/talkfiles/952b0e2854336082e41fb0ef8ef8dc97.talk"
[encoderrbspeex.cpp:103 ERROR] Error: invalid WAV file
[ttsfestival.cpp:29 INFO] Destroying instance

I suggest ignoring failed encoded files and continuing encoding and copying the files that suceeded.

Rockbox starts with remote, but doesn't respond to button presses except turning backlight on with build 6039eb05b-180313.
It works with deaeb73-161114 though.

Bug exists in the DEV builds for, at least, Sansa Clip+, Sansa Fuze+, and iPod Video for at least a year, although I cannot confirm this as I've only just now tracked down the problem. The issue was discovered because imagemagick occasionally selects 1x2,1x2,1x2 as the chroma sampling factor when converting an image.

To recreate this bug, convert any image using imagemagick to a JPEG with that chroma sampling factor and attempt to view it in Rockbox. What you will see is a nonsensical image to the size of the original JPEG. Any desktop image viewer, like eyeofgnome, renders the picture correctly.

I've also included a sample Rockbox logo generated in the faulty fashion along with this bug. To create it, run this command in a Unix-like with imagemagick and curl installed: 'curl -J -L "https://www.rockbox.org/rockbox400.png" | convert - -sampling-factor 1x2,1x2,1x2 -quality 100 folder.jpg'

For a couple of months my Sansa Fuze v2 has been crashing randomly when playing music. Most of the time I just get a white screen with an error message. The last message I got was :

'undefined instruction at 0006DC8C'

(I think that last number varies at each crash)

This didn't happen with v3.13, but it's been happening with every daily build I've tested IIRC.

It doesn't happen very often so it's hard to reproduce. I listen to music in public transports about twice a day and this happens not more than once a week. It seems to happen more often when the battery is low (less than 10%). It generally happens early in a playback session, when the first or second track is played.

Sometimes I don't get a white screen, but the program freezes and some parts of the interface are surrounded with white frames. I don't know if it's the same bug or if it's unrelated.

Note that I'm always listening to music on a microSD card, and I haven't tried on the main memory.

PS: I chose "Sansa Fuze+" in the OS list because I couldn't find Sansa Fuse v2.

Daily build c6d5cd7-170907

An idle power off can occur in recording mode. When it does, data loss occurs. This has already bitten me a few times.

Steps to reproduce (on battery, not charging):
1. Execute Settings > Manage Settings > Reset Settings
2. Set Settings > General Settings > Startup/Shutdown > Idle Poweroff to 1 minute
3. Reboot
4. Go to Recording mode
5. Note current Volume and Gain settings and then change them to something else and note the new settings. Don't start a recording; just leave it in “stop” mode (*not* record or record-pause).
6. Wait for automatic power off
7. Power back on and check recorder settings

Expected: Settings are what they were after being changed.
Actual: Settings reverted to what they were on boot.

This can cause the loss of entire recordings, too:

8. Go back to Recording mode.
9. Wait until just before Rockbox would power off, then start a recording (if the display goes to sleep, it comes back on a bit before powering off; start the recording as soon as it comes back on).

Expected: Recording is done as usual
Actual: Rockbox powers off anyway, without warning, less than a minute into the recording. The recording is lost (or if the file is there, it's unplayable; maybe this depends on the recording format used).

Dear Rockbox, long story short after doing update to the latest daily build c6d5cd7(2017-09-11), after playing music for around 30-40 minutes the screen start to freeze cannot scroll or select anything on the screen even turn it off is not possible but after few seconds it turn off by itself and can be turn on normally after that.

After upgrading from 3.13 to 3.14, when playing most of the ogg vorbis files in my library, a "beeping" sound sporadically occurs.

The sound is random (2 consecutive playbacks of the same track will beep on the same time).

All the files played fine with 3.13.
MP3 files play just fine (I have not tested other formats yet).

Possibly interesting facts :
Vorbis files with a lower bitrate (<100kpbs) seem to be less subject to this beep.
It seems beep never occurs when screen is on.

Today I've experience something which IMO should not happen.

I recorded vian the built in micro on my Sansa e200 v1, paused the recording (not stopped!). In this state, I plugged USB cable. After that, there was the following text in the system font on the display, and the player did not respond to any keys. It had to be restarted via very long pressing at On/Off.

The text is:

*PANIC*

usb_storage_init_connection
(): 00M
pc:0006B878 sp:000D3538

  A: 00069978
  A: 00069F80
  A: 0005326C

bt end

I've reproduced this three time in a row.

I have the official version 3.14 installed.

I downloaded this: https://www.youtube.com/watch?v=Lrb0dHKJBR4 using the youtube-dl python program. The file plays and seeks correctly in foobar2000 and MPC-HC. But, on my clip+, whether I seek 10 seconds or 10 minutes into the file, it ends up playing a position of the file previous to the one displayed. For example, if I seek 50 seconds forward from the beginning, it will play the file from the start, while the screen still displays as if it's playing from 50 seconds onwards. Seeking to the end of the file will have it play a section from about 2 minutes earlier than it should be, while the time display and music will continue until 1:14:20, with the file actually being 1:12:46.

I did not hear the files being played slower than they should be, so it seems it's only an issue when seeking.

I've confirmed this happens on every AAC file downloaded by youtube-dl, and that re-encoding the same file to AAC using NERO encoder makes the problem dissapear.

There is bug in rockblox: when you manage to push block exactly to the top of the field, game neither finishes with error, neither continues normally. this block starts growing when you destroy lines in the bottom.

I've made small video and put in into youtube (sorry for bad quality and sharpness :
http://www.youtube.com/watch?v=2gULp6yUms8

look into the left top and see what happens when lines are removed. bug is quite easy to reproduce. right side works like the left.

Creative ZEN device build 8fec364f6-170125

Steps:

1 Clear Running Time
2 Shutdown, to ensure Running Time clear takes effect
3 Launch Rockbox
4 Record wall clock time
5 Leave running for a few hours
6 View Running Time and compare with elapsed time on wall clock

Expected: Running Time equal to elapsed time
Observed: Running Time less than elapsed time by 2%

Note: battery_bench.txt times accord with elapsed time.

Where possible (i.e. the buttons aren’t needed for somethinig else), the PLAY button should go straight to the WPS (resuming as required) or radio.

These are almost the case, but on the H300 there are the following exceptions:

- Rockbox Info (PLAY performs the disk free space scan, same as SELECT)
- Playlist Viewer when selected from the Main > Playlists menu (PLAY returns to the menu above, same as LEFT)
- Sleep Timer (PLAY does nothing)
- Debug Manu (PLAY enters the selected item, same as SELECT)
- Browse x in Settings, where x = Themes, Fonts or .cfg/.wps/.rwps Files (PLAY returns to the menu above, same as LEFT). (Note that the plugin browser works fine!)

Similarly, the STOP button should stop playback, which is largely ok, except:

- In the Playlist Viewer (STOP does nothing)

I don’t have any other targets handy, but feel free to add any other suspect screens here.

I'm running Rockbox 3.11.2 on a Sansa Clip+.
I followed these steps:
- go to the Main Menu
- Files
- long press on <microSD1>
- Playlist Catalogue
- Add to New Playlist
I tried to save the playlist with a long press of the select button (not sure of the button's actual name; it is the button in the middle of the 4-way controller and the one that is usually used to select the highlighted option). I was returned to the Files menu. The playlist did not get saved, and there was no error explaining why.

As a result, I spent a long time assuming that long press of select was a "cancel" action, and tried short and long presses of every other button trying to save the playlist.

Workaround: instead of accepting the suggested filename, remove the "<" and ">" characters from the auto-entered filename ("/Playlists/<microSD1>.m3u8") to be able to save the playlist.

Suggested fixes: The filename suggested by Rockbox should not include "<", ">", or other un-saveable characters. In addition, if the user tries to save a file with invalid characters, a warning or error message should be posted (like the "Cancelled" message that briefly pops up when the power button is pressed to exit from the set-filename screen).

Build 575bd89 2016-12-19

Playing the attached zero-duration WMA '_ length 0.0s WMA.wma' causes crash:

Divide by zero at 6008D274
pc:6008D2&4 sp:600CC7DC
bt end

This WMA file was created by Goldwave and plays without crash in Windows Media Player, GoldWave and MediaMonkey.

Zero-length WAV and MP3 files (examples attached) don't cause a crash.

On the latest development iPod Video and ZEN simulators, MP3 and WAV are reported 'failed' and WMA crashes http://i.imgur.com/k3dKaSN.png http://i.imgur.com/CiYnVuH.png