dev builds
themes manual
device status forums
mailing lists
IRC bugs
dev guide

Search | Go
Wiki > Main > TargetStatus > Rockchip27xx (r20)
-- MarcinBukat - 2010-05-01

Fuzhou Rockchip Electronic produce a few families of SoC for portable devices. There are some technical documents floating around for RK27xx family which makes it possible platform for rockbox.

RK27xx SoC components:

  • ARM7EJ?-S (ARMv5TE? architecture) main core max. 200MHz
  • ZSP400 DSP core max. 160MHz
  • SDRAM controller
  • NAND flash controller
  • SD card controller
  • LCD controller
  • 3MPix Sensor for digital camera
  • DMA controllers
  • USB 2.0 host and device controllers (share the same PHY so only one at a time)
  • SPI
  • UART 1655
  • I2C? controller
  • I2S? controller
  • 3 32-bit timers
  • 4-channel PWM
  • Watchdog module
  • RTC module
  • 4-channel ADC converter
  • CODEC (24bit delta-sigma DAC + 16bit sigma-delta ADC) I2S? interface
  • 48 GPIO pins with interrupt capability


There are variety of generic devices build around this SoC. They share many similarities like around 3" touch display, microSD slot, 2,4,8,16,32 GB of internal flash (usually referred as Samsung flash). Below You will find a few pictures:






Odys MP X66 NEO

This features a RK2708 SoC, 2x 4 GB flash, 2.8" 320x240 TFT, micro SD card slot, built-in speaker, TV-Out, 1.3MP camera and FM Radio. The firmware extracting methods described below don't work. The device can be put into DFU mode (at least the vid:pid changes to 0x71b:0x3201), but rk27load (as of r30207) fails on stage1 upload.

Firmware extracting methods:

Firmware files are stored on separate, not exposed by default, system partition. In order to make this system partition visible one can put empty file with "magic" name in the root dir of the DAP. The most generic one seems to be RKLDSET.FLW (other possibilities are rkusb.tag, frk.tag, telecast.tag, telecast.sys). After placing such file in the root dir of the player, safely disconnect the device and unplug it from PC. Plugging it again should give you two drives - the main one (few GB in size) and system one (60-90MB in size). PLEASE BE EXTREMELY CAREFUL and do not delete files form system partition unless you know what you are doing. Removing "magic" file restore default behavior and system partition is not visible. There seem to be custom scsi commands which yield the same effect.

Boot sequence

The device start execution from 8kB bootrom (base 0x0). The bootrom searches for valid bootloader on nand flash starting from page 0. Data on the flash are stored in 512 bytes chunks followed by 16 bytes of metadata which will be referred as sectors later on. Bootrom checks the presence of magic string 0x55 0xAA 0xF0 0x0F and additionally checks if 3rd byte in metadata equals 0x69 at the beginning of every 64th page (it moves up to 50 times). If checks are passed, rom assumes the following data structure has been found:

ID block 0
offset length content comment
0 4 signature 0x55 0xAA 0xF0 0x0F
4 2 firmware year  
6 2 firmware date  
8 2 firmware ver1  
10 2 firmware ver2  
12 2 1st stage offset expressed in sectors, 0x04 usually
14 2 2nd stage offset expressed in sectors
16 20 reserved
36 2 firmware vendor  
38 470 reserved
508 2 boot code size in bytes (dram init + nand bootloader) 64kB max
510 2 reserved

ID block 1
offset length content comment
0 2 number of system reseved blocks Number of blocks occupied by the system, bad blocks included
2 2 system disk size in MB
4 500 reserved
504 2 1st ID block offset in sectors
506 2 2nd ID block offset in sectors
508 2 3rd ID block offset in sectors
510 2 4th ID block offset in sectors

ID block 0 is encrypted with RC4 encoding, ID block 1 is plain binary. ID block 2 and 3 seem to be unused (reserved for future extensions???). Values are stored in little-endian format.

First sector indicated by the 1st stage offset should contain dram initialization binary and is marked with magic 0x52 0x4B 0x32 0x37 ('RK27') at offset 0x1F8 (sector relative). The bootrom copies this initialization image to the buffer at 0x18200E00, executes dram init routine and returns. The rest of the bootloader image is loaded at 0x60000000 (begining of the DRAM) up to the indicated size in the header. Finally bootrom passes control to the loaded bootloader or in case something went wrong with reading bootloader from flash, bootrom falls back to usb DFU mode described in following section. Both dram init image and nand bootloader itself are stored in RC4 encoded form.

The flash bootloader relocates itself at 0x60700000 and loads BASE.RKW file from the system partition and passes control to the actual firmware. An entrypoint for image stored in BASE.RKW is at 0x60000000. The bootloader supports also USB in MSC mode for both user and system partiton as well as supports custom scsi commands.

There seem to be a few copies of the bootloader in consecutive flash blocks at the beginning of the nand (5 on the device I own).

DFU mode

rk27xx has some sort of DFU mode. The handler for this mode sits in 8kB SoC bootrom at address 0xAF0. The device in DFU mode has VID:PID = 0x71b:0x3201. Rockchip provides dedicated drivers for this mode as well as repair tool (RK27DM?.exe). This tool loads some binary blobs to the device from Rock27Boot?.bin file by means of usb control transfer. You can inspect the content of this binary blobs with help of rkboottool I have written. First image is sdram init and is running from iram. Second image is usb transfer handler for bulk transfers and is running from sdram (load base 0x60000000). The second stage is quite interesting - It has simple encrypt/decrypt based on XOR routine to decode blobs as well as some crc checking. Further transfers are handled by this routines and are of bulk type.

Clock settings

Datasheet floating around is misleading in section concerning clocks setup. SCU_DIVCON1 register bit2 selects the way ARMclk and HCLK are derived. If this bit is cleared ARMclk equals PLL out and HCLK equals PLL out/2. If this bit is set both ARMclk and HCLK are equal PLL out/2. Measurements show that SDRAM performance is related to HCLK (but not quite directly). Synchronous ARM:HCLK gives worst ram throughput than async setting with the same AHB bus frequency. LCD framerate is also related to HCLK.

test_mem results
ARMclk/HCLK/PCLK read write memset memcpy
200/100/50 97.0 MB/s 50.7 MB/s 50.7 MB/s 49.2 MB/s
100/100/50 80.0 MB/s 50.7 MB/s 50.7 MB/s 43.8 MB/s
264/132/66 (overclocked) 133.3 MB/s 68.0 MB/s 68.0 MB/s 66.6 MB/s
132/132/66 106.6 MB/s 66.6 MB/s 66.6 MB/s 57.1 MB/s
132/66/66 66.6 MB/s 34.0 MB/s 33.3 MB/s 33.3 MB/s
132/66/33 66.6 MB/s 34.0 MB/s 33.3 MB/s 33.3 MB/s
I Attachment Action Size Date Who Comment
mp5_1.jpgjpg mp5_1.jpg manage 11.4 K 01 May 2010 - 11:30 MarcinBukat  
mp5_2.jpgjpg mp5_2.jpg manage 5.2 K 01 May 2010 - 11:30 MarcinBukat  
mp5_2_1.jpgjpg mp5_2_1.jpg manage 72.7 K 01 May 2010 - 11:31 MarcinBukat  
mp5_3.jpgjpg mp5_3.jpg manage 89.9 K 01 May 2010 - 11:31 MarcinBukat  
mp5_4.jpgjpg mp5_4.jpg manage 69.1 K 01 May 2010 - 11:31 MarcinBukat rkboottool.c manage 10.0 K 05 Mar 2011 - 21:16 MarcinBukat Tool to inspect, unpack, descramble Rock27Boot?.bin recovery file
r20 - 14 Mar 2012 - 08:13:18 - MarcinBukat

Parents: TargetStatus
Copyright by the contributing authors.